防静电地板
Constant pursuit, continuous innovation and continuous improvement Quality comes first--Summer anti-static floor Your trusted anti-static flooring expert

contact details

contact number
点击这里给我发信息
Sales Manager: Mr. Zhang
Mobile: 13620206722
Landline: 0755-28272851
Website: mftlive.com

Position: Home > Products
Product Answer

Picture of anti-static floor construction technology and installation method

森美专注防静电地板厂家

I. Construction tools

Infrared level gauge, spirit level, screwdriver, small electric drill, cutting machine, steel tape measure, rivet gun, line drawing pen, rubber hammer, sucker, wrench, broom, etc.

Construction process:

弹线、找平 端部辅助支架安装 安装支柱架 安装搁栅 Grass-roots cleaning spring line, leveling installation of auxiliary support at the end installation of support brackets installation of joists   活动地板安装 收边条安装。 Leveling and leveling Raised floor installation Edge strip installation.

Detailed process:

首先清理地面。 1. First clear the ground.

Anti-static floor construction technology

2 Observe the layout of the room, install an infrared horizontal scanner, and mark the waist level on the surrounding wall, then find the lowest point and the highest point of the room, and calculate the average value from the ground to the board Required mounting height), calculate and adjust the height of the bracket.

Anti-static floor construction technology 2

3 595mm 处拴两条平行墙面的腊线,此腊线不易断裂和延伸,两条必须垂直分布。 Select a corner as the starting point, find a good level on the wall, and according to the height of the wall level, tie two wax lines parallel to the wall at a distance of 595mm from the wall . This wax line is not easy to break and extend, and the two must be vertically distributed.

Anti-static floor construction process 3

4 After pulling the parallel lines, screw the four pairs of brackets. Determine the height, lay the first board, be sure to tighten the fixing screws of the beam and the bracket, then adjust the plate with a level, and finally tighten the nut on the bracket.

Anti-static floor construction process 4

5 After leveling the first piece, lay two rows of floors vertically in the direction of the wax line. Note: The black plastic edges between the boards must be aligned and aligned.

Anti-static floor construction process 5

6 , After finishing the vertical two rows of floors, identify one direction. (Cannot be laid vertically any more). Note: A row must be left to cut and lay at the end. During the laying, the surface of the board must not be arbitrarily stepped to avoid affecting the flatness.

铺完最后一排后,应先固定四周墙角的角铁,再切割四周的地板。 7. After paving the last row, fix the corner irons around the corners first, and then cut the surrounding floors. Note: The level of the angle iron must be consistent with the level of the installed floor, and the back of the angle iron must be supported (wood support or triangular iron support).

Anti-static floor construction technology 6

8 After the angle iron is fixed, the small floor area to be cut is precise, and then the floor is cut and laid. If the ground socket needs to be installed, use a cutting machine to make holes according to the actual size.

Anti-static floor construction technology 7

9 , Anti-static floor trimming. Use a chainsaw to cut the motherboard, or install appropriate trimming components, at the edge of the wall, door frame, or pillar. The door is sealed with stainless steel or angle aluminum (right-angle type) with glass glue or nail fastening.

Anti-static floor construction technology 8

10 , After the floor is finished, you must check it in time to adjust the unevenness. Finally, the corners of the corners are filled with glass glue to fill the gap left during cutting.

若施工场地位于日夜温差大环境(如高海拔、温带或寒带地区)时,则All的收边处,都应预留约 3 mm 空隙以适应热涨冷缩。 11. If the construction site is located in a large temperature difference between day and night (such as high altitude, temperate or cold regions), about 3 mm clearance should be reserved at all edges to accommodate thermal expansion and contraction.

acceptance:

When the anti-static raised floor is completely laid, a comprehensive and detailed inspection of the entire project is required to improve the imperfections.

活动地板安装完后行走必须无声响,无摆动,牢固性好; 1. After the raised floor is installed , there must be no noise, no swing and good firmness when walking.

表面清洁,图案清淅,色泽一致,接缝均匀,周边顺直,板块无裂纹、掉角、起泡和缺边等现象; 2. The surface is clean, the pattern is clear, the color is consistent, the seams are uniform, the periphery is straight, and the plate has no cracks, corners, blistering, and missing edges;

各种面层邻接处镶边用料及尺寸符合设计要求和施工规范规定,边角整齐、光滑。 3. The bordering materials and dimensions of the adjacent areas of various surface layers meet the design requirements and construction specifications, and the corners are neat and smooth.

Anti-static floor

Various methods of closing edges are shown below:

Anti-static floor trim

share to:
hit count: Update Time: 2019-04-12 【 Print this page 】 【 Close